The quilt is analyzed on the production line. The balance can adjust the system device and is installed at the balance roller of the roll machine, so that our last control work can evenly feed cotton and ensure that the quality management of the roll meets the design requirements. The balance of the A076A roll machine can adjust the structure of the production device such as As shown in Figure 2-25. There are 16 parallel balance rods 2 under the balance roller 1. The position of the balance roller is not fixed, and the balance rod uses the knife edge holding the knife edge 3 as the fulcrum, which can be divided into two swings up and down , like the arm of the balance, so people call it the electronic balance pole. Carding machines are used to process cotton fibers and chemical fibers and belong to textile machinery. According to the spinning process, carding is an important process.
The front process of the carding machine is the opening and cleaning machine, and the latter process is the drawing frame (carding process) or the sliver coiler (combing process). Grinder A spinning machine that turns fiber strands into rovings. The main function is to draft and twist, and to wind the roving into a certain package to meet the processing requirements of the spinning frame.
Special equipment for the textile industry on the winder. As the last process of spinning and the first process of weaving, winding is the link between the past and the next.“bridge”Therefore, it occupies an important position in the textile field. When the cotton layer of the quilt production line communicates between the balance roller and the balance curved rod, if the cotton layer is too thick, the head end of the balance rod will be forced to squat, and its tail end will rise. The connecting rod (also known as the safety hook climbing) 6 makes the balance financial lever 7 be lifted with 8 as the fulcrum, and at the same time, the adjustment screws 10 that need to be connected to the left end of the balance economic lever model are lifted up, through the double-arm lever 11 ( The fulcrum 12) and the connecting rod 13 move the iron cannon belt fork 14 to the right, and the iron cannon belt 15 also moves to the small diameter end of the active iron cannon 16, and also moves to the large diameter end of the passive iron cannon 17. The speed of the student's active iron cannon is constant, and the passive iron cannon is driven by the belt 15. How does it drive the balance roller by selecting the worm 18, the worm wheel 19, and the gear 20? Therefore, to the small diameter of the active iron cannon Movement causes the belt, which slows down the market balance roller motor.
That is, when the passing cotton layer is too thick, the development of the cotton feeding speed is slowed down. On the other hand, when the cotton layer between the balance roller and the balance rod becomes thinner, due to the weight problem of the balance rod itself and the ecological balance using the action of the heavy hammer 9, the tail end of the balance rod gradually descends, and the balance has a lever left. Also down, the iron cannon belt begins to move to the left, the balance roller company accelerates, and the cotton feeder accelerates. Adjusting the position of the important pivot point 8 can change the amplitude of the constant swing of the level of the balanced financial leverage, so that the distance that the iron gun belt appears and moves left and right in China cannot be changed.
When the fulcrum moves to the right, the amplitude of the active swinging motion of the balance bar is significantly reduced, and the influence of the iron cannon belt directly on the mobile communication distance in my country is reduced. On the contrary, when the cultural fulcrum moves to the left, the iron cannon belt is used as the moving distance; it increases. The distance that the iron cannon belt can move must be established to adapt to the quantization of the lap and the density of the cotton layer, so that the change in the feeding speed of the balance roller caused by the change in the thickness of the feeding machine layer can be coordinated and just right.
Therefore, when there is a change during the commissioning process after installation, the scientific experiment teaching method must be used to optimize the adjustment and the most suitable position for the 901 to stand on. The balance of the quilt production line can adjust the control device to affect the longitudinal and uniform development of the roll. A good dog, you must note 23 when installing and adjusting: make the balance curved rod, balance the financial lever, 1 and the remote rod, belt fork and other parts to swing in a flexible way, the position of the support JE is correct, and the iron gun should be tensioned And appropriate to make full use of the uniform and stable role of the electronic balance adjustment system device.